edius and storm 2 no sound from timeline

[foundy]

just uninstalled prem 6.5 and have not formatted the system drive but installed edius 4.51 and there is no sound from the timeline

i had sound from prem but now can only hear sound if i play back via the playback monitor on edius

what have i done wrong??

also can i edit with edius in hd and still keep the storm card in

[antonsvideo]

do you have an amp and speakers connected to the audio out of the storm?

also, be sure your project setting is set to a storm profile and not OHCI

also, make sure the storm drivers are installed, if not, you won't see a storm profile

you can edit HD by selecting generic HDV OHCI, this bypasses the storm card

[GrassValley_BH]

What project setting are you in? If you're in a hardware project setting (not OHCI) then sound output will come from the selected hardware. Otherwise it will use the system sound device.

[GrassValley_BH]

Please keep to one post/thread for your question. Posting the same question under multiple threads is unnecessary.

[foundy]

still no sound from timeline

thanks for the answers but so far i still cannot get sound from timeline.
i have set up edius 4.51 with storm 2 and all drivers have been installed but even if i set the output as canopus, still no sound, so i then installed edius on a machine with no storm and just a firewire in and still no sound
what i am doung wrong?

i have tried many different configurations with no luck

[antonsvideo]

does the VU meter move when playing timeline?

do the clips on timeline show a waveform? is the audio enabled or muted on the left of timeline?

can we see a screen shot of your project settings

example

http://www.videoproductions.com.au/edius46/project-settings.gif

[foundy]

no sound from timeline

i am very new to edius as you have already guessed so really appreciate any help i can get

so far i have tried setting up many different confgs on edius and non give me sound

do i have a compatibilty conflict or what am i doing wrong

here are two screen shots one of the initial project settings and the other a full layout shot

i do not get any vu meter showing on either the play or rcrd monitors

i have two comps for edit work and the other one is with storm 2
but the same problem

is it really possible to use storm with edius 4.51??

[pjsssss]

Sound problems with Storm are almost always one of two problems.

1. Do you have the aduio out of the storm physically connected via a 1/8" plug to the audio in of your sound card.
2. Check in windows audio settings and make sure your audio in is not muted.

[Mr Bill]

is it really possible to use storm with edius 4.51??

My second PC is running Edius 4.6 with my DVStorm 2 card perfectly.

[antonsvideo]

i am very new to edius as you have already guessed so really appreciate any help i can get

so far i have tried setting up many different confgs on edius and non give me sound

do i have a compatibilty conflict or what am i doing wrong

here are two screen shots one of the initial project settings and the other a full layout shot

i do not get any vu meter showing on either the play or rcrd monitors

i have two comps for edit work and the other one is with storm 2
but the same problem

is it really possible to use storm with edius 4.51??

as clearly seen by your timeline screen shot, your video clip is missing the audio clip

here is a screen shot of a video clip that has audio and is showing a waveform

http://www.videoproductions.com.au/edius46/clip-sections.gif

also, as seen by your project settings, you are missing the storm drivers, I can only see OHCI

[SRsupport]

Tried the same but the OP is not really trying the suggestions.

And is will be real hard hearing audio if it is not there.

Steve

[SRsupport]

Steps:
1 reinstall Edius.
This will install the lastest storm drivers.
2 Now you will see storm hardware presets in the preset list.
3 Select a storm preset for your project
4 Put a clip with audio on the time line
(because it is impossible to get any audio out if there is no audio on the timeline)

If you select an ohci preset there is no way you will get audio out of the storm.
You need the have a storm preset out of the storm.
I also want to bet that you get no video out of the storm also because the drivers are not installed.
Really simple no drivers for the storm = No working storm because xp will not know what to do with the device.

Hope this helps.

Steve

[foundy]

config for storm 2 and edius 4.6

My second PC is running Edius 4.6 with my DVStorm 2 card perfectly.

so mr bill thanks for that answer but i would like to know how you configured your comp to get the two of them working well as so far i am still a bit lost

i have managed to get the tv output and sound from timeline by opening a clip but if i move the clip on the timeline up or down i lose sound but video is still fine
even if i put it back on the same v track it will not play sound but vdo is fine

also do i need to install storm video to capture as i see if i try to use edius on the storm bay it only gives s-vdo or composite

how do i capture with edius with the firewire via storm 2

[foundy]

time line sound probs

Steps:
1 reinstall Edius.
This will install the lastest storm drivers.
2 Now you will see storm hardware presets in the preset list.
3 Select a storm preset for your project
4 Put a clip with audio on the time line
(because it is impossible to get any audio out if there is no audio on the timeline)

If you select an ohci preset there is no way you will get audio out of the storm.
You need the have a storm preset out of the storm.
I also want to bet that you get no video out of the storm also because the drivers are not installed.
Really simple no drivers for the storm = No working storm because xp will not know what to do with the device.

Hope this helps.

Steve

thanks steve but i have installed the drivers for storm 2 and it all looks fine ]
i get tv monitor output matching the comp screen monitor but there is a another post from me with other q's which you maybe able to help with

cheers
david

[Mr Bill]

so mr bill thanks for that answer but i would like to know how you configured your comp to get the two of them working well as so far i am still a bit lost

i have managed to get the tv output and sound from timeline by opening a clip but if i move the clip on the timeline up or down i lose sound but video is still fine
even if i put it back on the same v track it will not play sound but vdo is fine

also do i need to install storm video to capture as i see if i try to use edius on the storm bay it only gives s-vdo or composite

how do i capture with edius with the firewire via storm 2

Well, I am lost as to why you have such problems.

I installed XP SP2 fresh,
had the DVStorm 2 card already connected to my MB,
installed my sound card drivers,
then restarted windows,
installed the latest drivers for my video card,
then restarted windows,
installed Edius 4,
then restarted windows,
updated to 4.6.
Then went ahead and installed any other applications....

Did NOT install any of those old drivers (as Edius has the latest)
You only need Edius or DVCapture to Capture.

That's all l did, works extremely well.
When all else fails, save all data and reinstall XP.

Bill