Originally posted by Timo
View Post
Announcement
Collapse
No announcement yet.
Edius NX, Edius 4 and Xplode Pro, problems, help!
Collapse
X
-
-
and all the transitions in Standard area don't work:
Xplode Pro/Standard
Leave a comment:
-
Originally posted by Roy Colquitt View PostUlisse,
What project settings are you using?
I use Sony FX camera (Pal HDV) and in Edius 4 I have these settings:
On the left NHX-E2 HD 50Hz and on the right HDCAM/DVCPRO HD/HDV 1080/50i
Rendering Format AVI Canopus HQ
These transitions don't work at all:
In Xpode Pro/3D Objects
3D Object Props
3D Object Pull
3D Object Transition
3D Object Wipe
and all the transitions in Standard area don't work:
Xplode Pro/Standard
Every other differents transitions work fine.
thanks
Leave a comment:
-
Originally posted by antonsvideo View Postcan you name such a transition so we can test and confirm
I know that many 3D object transitions are faulty in Xplode 4.5 Pro, however they work fine for standard definition 4:3 aspect
3D Object Props
3D Object Pull
3D Object Transition
3D Object Wipe
Can you test them please?
Thanks
Leave a comment:
-
can you name such a transition so we can test and confirm
I know that many 3D object transitions are faulty in Xplode 4.5 Pro, however they work fine for standard definition 4:3 aspect
Leave a comment:
-
Originally posted by syqkaduna View PostXplode for Edius or Xplode pro requires lots of PC resource,sometimes it can not be played realtime,you can add an 'in' point and an 'out' point,then render
them
If I make rendering I have the same problems.
I thank you of your help.
Leave a comment:
-
Guest repliedXplode for Edius or Xplode pro requires lots of PC resource,sometimes it can not be played realtime,you can add an 'in' point and an 'out' point,then render
them
Leave a comment:
-
Originally posted by mike0130 View PostSAPPHIRE RADEON X1950XT card should work fine. But in ATI control center in 3D section put all sliders to maximum and uncheck the "use application settings" everywhere in this 3D section. Press APPLY.
Now open EDIUS/Xplode EDIUS Config and then EDIUS/Xplode PRO Config.
Each of then in 3D render tab shoul be on "ATI Hardware Renderer". Press CONFIG button on the right side and check that "(1)Radeon X1950 Pro - Direct3D T&L HAL" is used. do not use one with software antialiasing!!!- but that option should be available- if not- your videocrd configuration is wrong (ATI control center ).
Settings should be identical for Xplode Pro and Xplode for Edius.
Good luck!
mike
3D Object Props
3D Object Pull
3D Object Transition
3D Object Wipe
When I add a transition and when the timeline run in the cutting clip (on the transition) I don't see any transition but the crossing between two clips without transition but sometime with a little trouble. Sometime I see in the Edius 4 monitor a full green page.
This is my proble.
A different thing.
In Xplode for Edius configurazion I don't see Ati card even if in it folder I have add XEnVidiaATI manually.
Can I solve my problems? Have I format my HD?
Thanks for your suggestions
Leave a comment:
-
SAPPHIRE RADEON X1950XT card should work fine. But in ATI control center in 3D section put all sliders to maximum and uncheck the "use application settings" everywhere in this 3D section. Press APPLY.
Now open EDIUS/Xplode EDIUS Config and then EDIUS/Xplode PRO Config.
Each of then in 3D render tab shoul be on "ATI Hardware Renderer". Press CONFIG button on the right side and check that "(1)Radeon X1950 Pro - Direct3D T&L HAL" is used. do not use one with software antialiasing!!!- but that option should be available- if not- your videocrd configuration is wrong (ATI control center ).
Settings should be identical for Xplode Pro and Xplode for Edius.
Good luck!
mike
Leave a comment:
-
Edius NX, Edius 4 and Xplode Pro, problems, help!
Hi, I have just assembled a new PC but I have many problems with Edius 4 and Xplode Pro. I use Sony FX7 HDV camera to shot.
I make an example.
If I drag a 30 seconds file on the Edius 4 timeline and I cut it on the midway some Xplode Pro transitions work fine and in realtime but some even don't work at all. I see thetwo clips withour transition.
Then if I use Xplode for Edius, on the Edius monitor I see green only.
I am worried and Saturday I'd like to format my HD but I am worried I will have the same problem.
Thanks for your info.
This is my config:
Pc-CONROE 6600 Core2Duo 2,4GHz Middle Tower Black
Scheda Madre: P5W HD DELUXE
MICROP. CONROE E6600 2,40GHz FSB 1066 4MB cache LGA775
RAM: 2 GB KINGSTON DDR800
SCHEDA VIDEO: SAPPHIRE RADEON X1950XT 256MB GDDR3
ALIM: ENERMAX INFINITY 620W
MASTERIZZ: PIONEER +/-R101
HD: 1 SATA DA 160 GB-SISTEMA
HD:2 SATA DA 160 GB RAID 0
HD:2 SATA DA 250 GB RAID 0
VENTOLA ARCTIC COOLING 12Vdc 120x120x25mm TACHIMETRICA
VENTOLA ARCTIC COOLING FREEZER 7 PRO X P4 SOCKET 775
Case full tower Cooler Master CM Stacker caseTags: None
Leave a comment: